Circular sheet metal bender KSL-2510

Fotografije uz članak 1

Circular sheet metal bender KSL-2510 is used for cold bending of plates with three rollers.

The stand of the machine is derived from welded steel sections and is rigid enough to take all the burden resulting from the operation of the machine. Therefore, no special foundation is required. Beneath the protective plate in the driving part there is a hydraulic generator, electric motor drive and the main electrical. The keyboard is placed in front of the rollers burner console and it can be downloaded when it is needed (for example flexing of the cone).

The upper roller is molded into a rolling bearing and has a  drive shaft rotations. The outer bearing is a rebuttable (by  hydraulic cylinders) due to removal of curved cylindrical shell. . Falling of beds is possible only after removal of side rollers, after unloading the upper roller . The inner roller remains in the same position after the overthrow of the outboard bearing.

The side rollers are also driven by a separate planetary gearing with its electric motors. All three planetary gear motors ara connected to the power supply through the frequency controller (inverter). Switching operation is performed by pressing and holding the right and left direction. RPM of rollers is elected by the potentiometer of the keypad. For easier presentation of pre-bending rollers remain locked through the  effect of dynamic DC electric brakes for 20 seconds after stopping the rotation. Effect of DC brake stops automatically in case of activation of turning to the left or right direction by pressing the appropriate buttons on the keyboard.

The side rollers are lifted and lowered independently by using hydraulic cylinders. Lifting and lowering of side rollers is performed by pressing the appropriate buttons on the keyboard. Current position of side roller  is read by the digital timer on the keyboard.

Parallel  motion of the rollers insures one tosional shaft whose arms are  attached to the bearing housing rolls through the brace. 

SPECIFICATIONS AND BENDING FEATURES
Installed (rated) horsepower 11.2 kW
Electical connection 3x400 V, 50 Hz, 32 A
Control voltage 24 VDC
Drive rollers On all three cylinders, each cylinder separate motor, progressively turing the speed control
Rising and lowering the side rollers hydraulic cylinders  
Digital readout position of the side rollers  
Turning down beds of the upper roller hydraulic cylinder  
Speed of the passage plate (continuous regulation) 1 – 7 m / min
Diameter of the side rollers 260 mm
Diameter upper roller 255 mm
Working length of rollers 2550 mm
Machine dimensions (LxWxH) 4500 x 1250 x 1300
Weight (wthout the upper side and a recieving device) Approx 6500 kg
The possibility of bending metal sheet for diameter ≥ 1000 mm  
Maximum width of sheet 2550 mm
Maximum thickness without pre-bending 12 mm
Maximum thickness with pre-bending 10 mm
The possibility of bending metal sheet for diameter ≥ 500 mm  
Maximum width of sheet 2550 mm
Maximum thickness without pre-bending 10 mm
Maximum thickness with pre-bending 8 mm
Maximum thickness of the bending diameter of ≥ 1000 mm  
Maximum width of sheet 2550 mm
Maximum thickness without pre-bending 20 mm
Maximum thickness with pre-bending 16 mm
Maximum bending thickness „t“, depending on the width oft he sheet „b“ in mm can be calculated usig the formula  

Some of the obtained values are shown in the table below

b/width 2500 2000 1500 1100 850 660 400 275 200 150 95 65
t/thickness 12 13 14 16 18 20 25 30 35 40 50 60

A profile of maximum height of 65 mm and maximum torque W≤40(cm)^3 can be curved

NOTE :
All the above stated figures are for bending to the limits of plasticity 240 N/mm² (Eg. S 235 JR)  

Kontakt

Kalmana Mesarića 26,
40323 PRELOG

tel: +385 (40) 645-344 +385 (40) 645-324
Fax:+385 40 645-408 +385 40 646-105

e-mail: info@komet.hr

* - obavezna polja